How to Change Ford Escape Rear Brake Drums

The Ford Escape has drum-in- rear disc brakes. This form of brake drum are less of a challenge to change versus more common actuator form of rear disc brakes.

The replacement process of the brake drum on the drum-in-hat system is just like the replacement procedure of the front brake shields.

Due to the absence of an actuator built into the rear caliper, the piston is usually collapsed without a particular caliper piston tool.

This repair can be completed within just two hours, making use of basic hand methods.

Block the the front wheels, using steering wheel chocks, and position a floor jack under the rear-trailing arm on one side of the automobile.

Tools You'll Need

• Wheel Chocks
• 3 Ton Aluminum and Steel Garage Jack
• Socket set
• Screwdriver set
• Ford ESCAPE Rr Drum Front Brake Pads and Brake Rotors OEM Replacement Direct Fit Brake Kit
• Silaramic Brake System Grease - 5 oz.
• TEKTON 24320 1/4-Inch Drive Click Torque Wrench, 20-200-Inch/Pound

Search over 100,000 Ford Escape Auto Parts and Accessories and save up to 70% on Amazon -Click here to Find Your Specific Model Year

 Place jack appears under the rear sub-frame and reduce the jack to aid the weight of the Escape. Remove the trunk wheels and position them, along while using lug nuts, behind the automobile.

Remove the a pair of caliper slide pins (located on the back of this caliper in the Escape) that secure the brake caliper towards caliper support. Fall the caliper above the brake rotor.


Open the bleeder screw over the brake caliper and utilize a C-clamp to shrink the caliper piston into your caliperhousing. Shut the bleeder prop before removing this C-clamp. Apply a compact amount of silicon brake grease towards caliper slide hooks.

Slide the outdated brake drum out of your caliper support group. Apply a smaller dab of silicon brake grease towards contact points on the backing plates connected with the brake shields, then slip them into put on the caliper assistance.

Slide the caliper above the new drum and secure the crooks to the caliper assistance, using the
fall pins. Torque this slide pins to be able to 26 foot-pounds, by using a torque wrench. Reinstall this wheels.

Lift the Ford from the jack stands and get rid of the stands. Lower the automobile to the ground and torque this lug nuts to be able to 80 foot-pounds.


Push the brake pedal several times before test-driving.

Always exercise caution when working on a vehicle put on jack stands.


Resources:

Ford Escape & Mazda Tribute: 2001 thru 2011 - Includes Mercury Mariner (Haynes Manuals)

Ford Escape Door Lock Actuator Repair

Ford uses any modular design doorway lock actuator. When one of those sealed
units neglects, there is no way to repair the idea, so replacement can be your only
option.

Your Ford dealer can supply you with the correct actuator for the
year and model should you give a parts salesperson your vehicle identification
number. Common hand methods are all that is required to access and replace
the hit a brick wall actuator.


Tools You'll Need: 

• Door Panel Window Removal Tool Kit
• Stanley 68-012 All-in-One Screwdriver
• Stanley 66-344 4-in-1 Pocket Screwdriver
• Stanley FL5W10 5 Watt LED Waterproof Rechargeable Spotlight
• Stanley 92-804 30 Piece Socket Set
• Dorman 746-149 Door Lock Actuator

Grasp the windowpane side edge in the upper inner door trim together with your
fingertips. Pull it straight retreat from the door release a the catches. inches
Gently pry up on the narrow end in the armrest switch panel to get rid of it
from the particular armrest.

Eliminate the hex head twist located behind the particular switch panel.
Press the connection lock tab in and pull the connectors from the switches.
The switch panel has become completely free and will be removed from the door.
Eliminate the door trim screen by sliding it sheer the door.

Remove the insulating sheet from the door. This is glued towards door and is usually
removed by pulling gently for the sheet to launch the glue. inches


Disconnect the three rods with the door latch. Fly  rod  is very easily removed by
inserting the blade of the screwdriver in the opening between your two lock
navigation bars. This will wide open the tabs adequate to slide the particular rod out. This clamp on Fly  rod
 is hinged one side, simply open one other side to launch the rod.

This yellow clamp in rod pushes journey rod, but stays within the door latch. inches
Unscrew the 3 Torx screws and get rid of the latch from the entranceway.

Removal will require turning the latch a bit to clear the particular window channel. inches
Lift the tabs and unplug the particular electrical connector from the actuator.


Hold the latch solidly and pry up on the spring tabs, which holds the particular actuator to
the particular latch. When the particular tab is completely raised slide the particular actuator toward
you and journey latch.

Slide the new actuator into position for the door latch. This spring tab can
lower and fastener the actuator set. Plug the connection back onto the particular
actuator.

Install the particular three screws and tighten firmly. Substitute the three rods; they
will only accomplish the lock they belong to.

Replace the entranceway panel, switch screen and upper reduce.
To avoid cracking the plastic, do not attempt to take away a plastic doorway
panel in extremely winter.
Resources:

Ford Escape & Mazda Tribute: 2001 thru 2011 - Includes Mercury Mariner (Haynes Manuals)

How to Find & Replace 2003 Ford Escape Brake Light?

The 2003 Ford Escape's brake Light is stored inside taillight case in the back with the vehicle. This case likewise holds the backup lamp and the rear turn indicate bulb. Ford doesn't specify a replacement interval for this Escape's brake lights—you'll simply have to replace the bulbs while they burn out. It's a wise idea to check the operation of your exterior bulbs the moment a month. inch


Tools You'll Need:

• Mechanix Wear M - Pact Gloves
• 29 in 1 Magnetic Slotted Philips Torx Screwdriver Set
• Sylvania 3157A/4157A ST BP SilverStar 27-Watt High Performance Signal Light

Turn the headlight manage to "Off" and shut the engine down. Wear gloves to avoid in contact the replacement lamp directly.

Open this cargo door.

Find and eliminate the two Phillips screws for the taillight case which has a screwdriver. They are for the inboard side with the case and just visible when this cargo door will be open. "


Grasp the case and pull it straight to remove it. Don't tilt or swing it. Locate the braking system light bulb—it's the second bulb from the most notable. "

Turn the trunk of the brake bulb socket counterclockwise and remove it. Gently grasp this old bulb and pull it outside the socket. "

Connect the replacement bulb towards socket. Insert the socket back to the case and turn it clockwise.

Push the case back into the place. Insert and tighten the Phillips anchoring screws. Close the Escape's freight door.


Resources:

Ford Escape & Mazda Tribute: 2001 thru 2011 - Includes Mercury Mariner (Haynes Manuals)